Motec ACL VIM Manual de usuario descargar pdf (Pagina 84)

80 Appendices

Appendix K: CAN Bus Wiring

The CAN bus should consist of a twisted pair trunk with 100R (0.25 watt)

terminating resistors at each end of the trunk.

The preferred cable for the trunk is 100R Data Cable but twisted 22# Tefzel is

usually OK.

The maximum length of the bus is 16 m (50 ft)

CAN Devices (such as MoTeC ACL, ADL2, BR2 etc) may be connected to the

trunk with up to 500 mm (20 in) of twisted wire.

CAN-LO

CAN-HI

100R

CAN-LO

CAN-HI

500mm

Max

<< CAN Bus >>

100R Terminating

Resistors at each

end of the CAN Bus

CAN-LO

CAN-HI

CAN-LO

CAN-HI

These wires must be Twisted

Minimum one twist per 50 mm (2 in)

CAN Device

eg ACL

CAN Device

eg ADL2

CAN Device

eg VIM

1 2 ... 79 80 81 82 83 84 85 86 87 88 89 ... 98 99

Contents 1
Introduction 5
Overview 6
MoTeC Overview 3 7
Measurement Devices 7
Options 7
Memory Card 7
More Information 7
PLM Lambda Meter 10
Telemetry Radio System 10
MoTeC Overview 7 11
Operation 13
Display 14
Display Elements 15
Centre Numeric Display 16
12 Operation 16
Numeric Displays 16
Display Modes 17
14 Operation 18
Practice Mode 18
Warm-up Mode 18
Display Formatting 19
Data Logging 20
MoTeC Operation 17 21
Memory Filling Options 21
Logging Rate 21
Retrieving the Logged Data 23
Functions & Calculations 24
Measurement Inputs 25
Input Basics 26
Input Types 27
24 Operation 28
MoTeC Operation 25 29
26 Operation 30
Auxiliary Outputs 31
Communication Ports 31
28 Operation 32
Serial Communications Ports 32
ACL Central Logger 34
ACL Setup 35
ACL Firmware 35
Connected Devices 36
VIM Setup 37
VIM Firmware 37
ADL2 & SDL Display 38
MDD Display 39
BR2 Beacon Receiver 39
SLM Shift Light Module 40
E888 / E816 Expanders 41
MoTeC GPS 42
ECU Connection via RS232 44
ECU Connection via CAN 44
ECU Setup 45
ACL Manager Software 47
Mouse & Keyboard 48
Main Menu 48
Toolbar 49
Online / Offline 49
Configuration 49
Configuration Files 50
Changing the Configuration 51
48 ACL Manager Software 52
Updating 52
Matching Versions 52
Configuration File Version 52
Channels 54
Channel List 55
Channel Properties 55
Selecting Channels 56
Conditions Overview 58
Checking Operation 59
Sensor Zeroing 60
Details Editor 60
Windows Keyboard Use 61
58 Windows Keyboard Use 62
Using the Selected Item 62
Check Box 63
Radio Buttons 63
60 Windows Keyboard Use 64
Appendices 66
MoTeC Appendices 63 67
Telemetry Option 67
Remote Logging Option 67
Analogue Inputs 69
66 Appendices 70
VIM Pull-up Resistor Pins 70
VIM Speed Inputs 71
68 Appendices 72
MoTeC Appendices 69 73
E888/E816 73
70 Appendices 74
Other Devices 74
MoTeC Appendices 71 75
Usage: 75
Options: 75
72 Appendices 76
MoTeC Appendices 73 77
RS232 Errors 77
General CAN Errors 77
74 Appendices 78
"VIMCOM" Errors 78
MoTeC Appendices 75 79
76 Appendices 80
MoTeC Appendices 77 81
78 Appendices 82
M800 / M880 82
MoTeC Appendices 79 83
M48, M4 (pre M4e) and M8 83
Appendix K: CAN Bus Wiring 84
Appendix L: Wire Information 85
For 5 Pin 86
MoTeC Appendices 83 87
84 Appendices 88
VIM 5 Pin Connector 88
VIM 55 Pin Connector 88
MoTeC Appendices 85 89
86 Appendices 90
MoTeC Appendices 87 91
88 Appendices 92
MoTeC Appendices 89 93
ACL 5 Pin Connector 93
ACL 22 Pin Connector 93
90 Appendices 94
MoTeC Appendices 91 95
92 Notes 96
MoTeC Notes 93 97
94 Notes 98
MoTeC Notes 95 99

Comentarios a estos manuales

Sin comentarios

Motec ACL VIM Manual de usuario Pagina 84

Comentarios a estos manuales

Relacionado con productos y manuales para Hardware Motec ACL VIM